HUAWEI网络设备恢复Console口密码
阅读原文时间:2022年01月14日阅读:1

密码遗忘

本章介绍了Console口丢失的处理方法,建议用户妥善保管密码,并定期修改。

恢复Console口密码

设备提供如下方法恢复Console口密码。
•方法一:通过STelnet/Telnet登录设备修改Console口密码。(推荐)
•方法二:在BootROM下配置清除Console口密码启动后,修改Console口密码。
•方法三:在BootROM菜单下取消设置下次启动配置文件,设备以空配置启动后修改Console口密码。

方法一:通过STelnet/Telnet登录设备修改Console口密码。

以下涉及的命令行及回显信息以STelnet登录设备修改Console口密码为例。如果用户拥有STelnet账号,并且具有3级或更高的权限,则可以通过STelnet登录到设备后修改Console口密码,然后保存配置。

1.使用STelnet账号登录设备,并确认当前账号有3级或更高的权限。
使用display users命令查看当前设备所有登录用户。其中带“+”标记行为当前用户,记录对应的编号VTY1。

display users
User-Intf Delay Type Network Address AuthenStatus AuthorcmdFlag
129 VTY 0 00:23:36 TEL 10.135.18.67 pass no Username : Unspecified

  • 130 VTY 1 01:20:36 TEL 10.135.18.91 pass no Username : Unspecified

    131 VTY 2 00:00:00 TEL 10.135.18.54 pass no Username : Unspecified

使用display user-interface命令可以显示所有用户的权限,确定VTY1对应的等级为15,有权限修改Console口密码。

display user-interface
Idx Type Tx/Rx Modem Privi ActualPrivi Auth Int
0 CON 0 9600 - 15 - P -

  • 129 VTY 0 - 15 15 P -
  • 130 VTY 1 - 15 15 P -
  • 131 VTY 2 - 15 - P -
    132 VTY 3 - 15 15 P -
    ……

2.修改Console用户的密码,以修改为密码认证,密码为“huawei@123”为例。

system-view
[HUAWEI] user-interface console 0
[HUAWEI-ui-console0] authentication-mode password
[HUAWEI-ui-console0] set authentication password cipher huawei@123
[HUAWEI-ui-console0] return

3.为了防止重启后配置丢失,保存配置。

save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.

方法二:在BootROM下清除Console口密码登录后,修改Console口密码。

设备的BootROM提供了清除Console口密码的功能,可以在用户使用Console口登录的时候跳过密码检查。这样系统启动后除了不需要输入Console密码外,与正常启动相同,也会完成所有配置加载。设备启动后重新配置验证方式和Console口密码,然后保存配置。

注意:
•要进入到BootROM菜单需要重启设备,会导致业务中断,请视具体情况做好设备备份,并尽量选择业务量较少的时间操作。
•清除Console口密码登录后请马上配置新的密码。
•在此操作过程中不要对设备进行下电。

1.用串口线连接设备,然后重启。当出现“Press Ctrl+B to enter BootROM menu…”(V200R002及V200R003版本)或者“Press Ctrl+B or Ctrl+E to enter BootROM menu …”(V200R005及以后发布的版本)打印信息时,按下“Ctrl+B”或者“Ctrl+E”并键入密码(缺省为“Admin@huawei.com”,V100R006C03之前版本可能为“huawei”),进入BootROM主菜单。
2.清除Console口登录密码。

      BootROM  MENU

1. Boot with default mode  
2. Enter serial submenu  
3. Enter startup submenu  
4. Enter ethernet submenu  
5. Enter filesystem submenu  
6. Modify BootROM password   //V200R006及之前版本:Modify BootROM password V200R007及之后版本:Enter password submenu  
7. Clear password for console user  
8. Reboot  
(Press Ctrl+E to enter diag menu) 

Enter your choice(1-8): 7

Note: Clear password for console user? Yes or No(Y/N): y

Clear password for console user successfully. Choose "1" to boot, then set a new password.
Note: Do not choose "8. Reboot" or power off the device, otherwise this operation will not take effect.

3.根据设备的提示,在BootROM主菜单下选择“1”启动设备。
4.完成系统启动后,通过Console口登录时不需要认证,登录后配置Console口密码,以修改为密码认证,并修改密码为“huawei@123”为例。

system-view
[HUAWEI] user-interface console 0
[HUAWEI-ui-console0] authentication-mode password
[HUAWEI-ui-console0] set authentication password cipher huawei@123
[HUAWEI-ui-console0] return

5.为了防止重启后配置丢失,保存配置。

save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Save the configuration successfully.

方法三:在BootROM菜单下取消设置下次启动配置文件,设备以空配置启动后修改Console口密码。

在BootROM下取消设置下次启动配置文件,设备会以空配置(出厂配置)启动。启动后将原配置文件导出,手动修改其中关于Console口登录的配置。将修改后的配置文件重新上传至设备,配置设备以修改后的配置文件启动,重启后的设备将无需输入Console口登录密码。(以下举例以Console口下配置了Password认证为例,其它认证方式以设备实际情况为准。)

注意:
•要进入到BootROM菜单需要重启设备,会导致业务中断,请视具体情况做好设备备份,并尽量选择业务量较少的时间操作。
•在此操作过程中不要对设备进行下电。
•V200R010及之后版本Console口默认为AAA认证,如果空配置启动后没有修改认证方式,配置设备以删除认证方式后的配置文件启动时,重启后的设备需要输入缺省的用户名admin和密码admin@huawei.com,此种情况下的回显,以设备实际显示为准。

1.用串口线连接设备,然后重启,当出现“Press Ctrl+B to enter BootROM menu…”(V200R002及V200R003版本)或者“Press Ctrl+B or Ctrl+E to enter BootROM menu …”(V200R005及以后发布的版本)打印信息时,按下“Ctrl+B”或者“Ctrl+E”并键入密码(缺省为“Admin@huawei.com”,V100R006C03之前版本可能为“huawei”)后进入BootROM主菜单。
2.清空启动配置文件,使设备以空配置启动。

      BootROM  MENU

1. Boot with default mode  
2. Enter serial submenu  
3. Enter startup submenu  
4. Enter ethernet submenu  
5. Enter filesystem submenu  
6. Modify BootROM password   //V200R006及之前版本:Modify BootROM password V200R007及之后版本:Enter password submenu  
7. Clear password for console user  
8. Reboot  
(Press Ctrl+E to enter diag menu) 

Enter your choice(1-8): 3

   Startup Configuration Submenu

1. Display startup configuration  
2. Modify startup configuration  
3. Return to main menu

Enter your choice(1-3): 2

Note: startup file field can not be cleared
'.'=clear field; =quit; Enter=use current configuration

startup type(1: Flash)
current: 1
new :

Flash startup file (can not be cleared)
current: HUAWEI-v200r008c00.cc
new :

saved-configuration file
current: vrpcfg.zip
new : . //清空当前值

patch package
current:
new :

   Startup Configuration Submenu

1. Display startup configuration  
2. Modify startup configuration  
3. Return to main menu

Enter your choice(1-3): 3

3.在BootROM主菜单下选择“1”启动设备。
4.完成系统启动后,设备会恢复为出厂配置。V200R009及之前版本通过Console口登录时,提示设置Console口密码,以密码为“huawei@123”为例。

An initial password is required for the first login via the console.
Continue to set it? [Y/N]:y
Set a password and keep it safe. Otherwise you will not be able to login via the console.

Please configure the login password (8-16)
Enter Password: //输入huawei@123
Confirm Password: //再次输入huawei@123

V200R010及之后版本通过Console口登录时,提示输入Console口的默认用户名和密码,之后会提示修改密码,此时必须修改密码,以密码为“huawei@123”为例。

Login authentication

Username:admin
Password: //输入admin@huawei.com
Warning: The default password poses security risks.
The password needs to be changed. Change now? [Y/N]: y
Please enter old password: //输入admin@huawei.com
Please enter new password: //输入huawei@123
Please confirm new password: //再次输入huawei@123
The password has been changed successfully.

5.恢复原配置。当前设备为默认的出厂配置,若希望恢复设备原配置,又不想保留原配置文件中关于Console密码的配置,可以下载原配置文件到PC上,手动删除Console下配置后,上传至设备,指定为下次启动文件,重启设备。

a.配置设备为FTP服务器。

system-view
[HUAWEI] ftp server enable
Info: The FTP server is already enabled.
[HUAWEI] vlan 10
[HUAWEI-vlan10] interface vlanif 10 //配置VLANIF10作为管理接口。
[HUAWEI-Vlanif10] ip address 10.110.24.254 24
[HUAWEI-Vlanif10] quit
[HUAWEI] interface gigabitethernet 0/0/10 //GE0/0/10为使用Web网管登录Switch的PC与Switch相连的物理接口编号,请按照实际现网情况进行选择。
[HUAWEI-GigabitEthernet0/0/10] port link-type access
[HUAWEI-GigabitEthernet0/0/10] port default vlan 10
[HUAWEI-GigabitEthernet0/0/10] quit
[HUAWEI] aaa
[HUAWEI-aaa] local-user huawei password irreversible-cipher huawei@123
[HUAWEI-aaa] local-user huawei ftp-directory flash:
[HUAWEI-aaa] local-user huawei service-type ftp
[HUAWEI-aaa] local-user huawei privilege level 15

b.下载原配置文件vrpcfg.zip到PC。

C:\Documents and Setting\Administrator> ftp 10.110.24.254
连接到 10.110.24.254。
220 FTP service ready.
用户 (10.110.24.254:(none)): huawei
331 Password required for huawei.
密码:
230 User logged in.
ftp> get vrpcfg.zip
200 Port command okay.
150 Opening ASCII mode data connection for directory list.
226 Transfer complete.
ftp: 收到 981 字节,用时 0.01秒 981000.00千字节/秒.

c.在PC上解压后使用文本编辑工具(建议用系统自带的文本编辑工具)打开并删除Console口认证配置,删除后重新压缩成vrpcfg.zip文件。需删除的配置如下所示:

user-interface maximum-vty 15
user-interface con 0
authentication-mode password //需手动删除
set authentication password cipher %@%@:*IB+w7j~""GlU$0-;\#m@Jw%@%@ //需手动删除

user-interface con 0
authentication-mode aaa //需手动删除
user privilege level 15 //需手动删除

6.将修改后的配置文件保存后,上传到设备,替换原配置文件。

ftp> put vrpcfg.zip
200 Port command okay.
150 Opening ASCII mode data connection for directory list.
226 Transfer complete.
ftp: 发送 981 字节,用时 0.00Seconds 978000.00千字节/秒.

7.设置修改后的配置文件为下一次启动配置文件,选择不保存配置重启设备。

startup saved-configuration vrpcfg.zip
Info: Succeeded in setting the configuration for booting system.
reboot fast
System will reboot! Continue ? [y/n]:y

8.重启后,会再次提醒设置Console登录密码,输入一个安全并方便自己记忆的密码后,回车,进入命令行界面。

手机扫一扫

移动阅读更方便

阿里云服务器
腾讯云服务器
七牛云服务器

你可能感兴趣的文章