Raspberry Pi & GPIO
阅读原文时间:2023年07月12日阅读:1

Raspberry Pi & GPIO

pinout === pin out / p in out

pi@raspberrypi:~ $ pinout
,--------------------------------.
| oooooooooooooooooooo J8     +====
| 1ooooooooooooooooooo        | USB
|                             +====
|      Pi Model 3B  V1.2         |
|      +----+                 +====
| |D|  |SoC |                 | USB
| |S|  |    |                 +====
| |I|  +----+                    |
|                   |C|     +======
|                   |S|     |   Net
| pwr        |HDMI| |I||A|  +======
`-| |--------|    |----|V|-------'

Revision           : a22082
SoC                : BCM2837
RAM                : 1024Mb
Storage            : MicroSD
USB ports          : 4 (excluding power)
Ethernet ports     : 1
Wi-fi              : True
Bluetooth          : True
Camera ports (CSI) : 1
Display ports (DSI): 1

J8:
   3V3  (1) (2)  5V
 GPIO2  (3) (4)  5V
 GPIO3  (5) (6)  GND
 GPIO4  (7) (8)  GPIO14
   GND  (9) (10) GPIO15
GPIO17 (11) (12) GPIO18
GPIO27 (13) (14) GND
GPIO22 (15) (16) GPIO23
   3V3 (17) (18) GPIO24
GPIO10 (19) (20) GND
 GPIO9 (21) (22) GPIO25
GPIO11 (23) (24) GPIO8
   GND (25) (26) GPIO7
 GPIO0 (27) (28) GPIO1
 GPIO5 (29) (30) GND
 GPIO6 (31) (32) GPIO12
GPIO13 (33) (34) GND
GPIO19 (35) (36) GPIO16
GPIO26 (37) (38) GPIO20
   GND (39) (40) GPIO21

For further information, please refer to https://pinout.xyz/
pi@raspberrypi:~ $ 

Pinout

引脚排列

https://pinout.xyz/

GPCLK0

https://pinout.xyz/pinout/pin7_gpio4

BCM 17

https://pinout.xyz/pinout/pin11_gpio17

3.3 v 正极 +,高电平

5v 正极 +,高电平

Ground 负极 - ,接地,低电平

general purpose input/output

普通 GPIO,如 GPIO 17,可以控制电平的高低状态,改变 LED 的显示状态

特殊 GPIO, 如 ,一般高级功能才用的到,暂不讲解

电路图,

电源正极(3v3 pin) => 电阻 => LED 正极(长脚) => 电源负极(GND pin)

面包板
电阻 200Ω (大于 50Ω? 200KΩ 不好使?)
LED 长正短负
杜邦线,红正黑负

面包板,正负极是安排划分的???

红线接正极,黑线接负极

220欧姆电阻器, 200k is not ok

触觉 按钮 开关

led 长针是正极,短针是负极

https://youtu.be/XrlR7cHSltw?t=370

You can test whether your GPIO pins and LEDs are working by building the circuit below. You can use any resistor over about 50Ω.

The LED is connected directly to the GND pin and the 3V3 pin via the 330 Ohm resistor, and should light up.

Be sure to connect your LED the correct way round; the longer leg should be connected to the 3V3 pin:

GPIO with Scratch 2

GPIO with Python

https://www.cnblogs.com/xgqfrms/p/13474349.html

https://www.raspberrypi.org/documentation/usage/gpio/



xgqfrms 2012-2020

www.cnblogs.com 发布文章使用:只允许注册用户才可以访问!